Coming soon

Bleno 3D – flight guide

How to fly for a good 3D model

Bleno 3D calculates a 3D model from your own drone's photo series. How good the model turns out depends above all on the flight – here you'll find the procedure for your drone class and your flight app, plus the legal basics.

Bleno 3D cannot be booked yet. This guide already shows how the flight will work – we will announce the launch in the app and in the newsletter.

The principle: grid, orbit and low orbit

Whatever your drone and app, a good model needs these capture passes over the same property:

Vertical grid
The camera points straight down (a gimbal pitch from about 70° below the horizon counts as vertical), and the drone flies a grid over the whole roof, about 20–30 m above the ridge. This captures the roof planes.
Oblique orbit (35°–45° below the horizon)
One or two circles around the building with the camera tilted, one photo every 5–10°. In the test flight the gimbal pitch was 35°–45° below the horizon at a height of about 10–25 m (a guide value from that test flight, not a fixed rule) – Bleno counts anything between 15° and 70° below the horizon as oblique. This captures the upper facade areas and edges such as ridge and hip.
Low orbit with an almost horizontal camera
Another, low circle at a height of about 1–4 m with the camera close to horizontal. Without this pass, the facade directly under the roof overhang is missing – in the model this shows up as a ragged gap around the house. This pass always belongs in the series, not only for facade measurements.
Second low orbit close to the house
For the zone directly under the roof overhang, the first low orbit is often not enough: fly a second, tighter circle about 2–3 m from the facade, roughly at eaves height, with the camera tilted slightly upwards (about +10° to +20° above the horizon). Not every drone and app lets the camera tilt above the horizon or offers this in an automatic grid flight – check this in your app before the flight. Fly this pass by hand only: the obstacle detection of many drones covers upwards and sideways only partly or not at all, and at this distance there is a real risk of colliding with the roof overhang and gutter.
Transition photos at medium height
Between the low and the high oblique orbit, fly another row of photos at medium height. Without this bridge, the calculation often finds no common image points between the photos near the ground and the high photos, and the series falls apart into two separate model parts.
Facade orbit
For facade measurements (painting, rendering, scaffolding), also fly a separate orbit closer along the wall, with the camera pointing at the facade as squarely as possible, rather than only around the whole building.
Hand-held photos in recesses and under canopies
No drone reliably reaches recesses, building corners and areas under covered terraces or canopies – photograph these spots by hand as well, with at least 70% overlap with the neighbouring photos.

Guide values for the series

  • 80–200 photos are a good guide value (Bleno calculates from at least 50 and at most 400)
  • Overlap between neighbouring photos: about 75% front, 70% side – better one photo too many than a gap
  • GPS position in practically every photo (Bleno requires GPS in at least 90% of the series)
  • Photos as JPEG, without changing the camera during the flight
  • An overcast sky is ideal: no hard shadows, no reflections, little wind

Without ground control points, a reference distance measured on site remains mandatory in the model – even with an RTK drone: the drone's GPS gives consistent proportions but no reliable scale. In our test flight (test series of 219 photos, example camera DJI FC9313), the hip measured 1.8% above the check measurement without a reference distance, using the GPS scale only – evidence of why the reference distance is mandatory, not an accuracy promise for the typical case. The reference distance does not need the roof: before the flight, lay out two clearly visible markers (chalk cross, plate, cone) exactly 10 m apart with a tape measure and set these two points as the reference in the model – or laser-measure a house wall at its base from corner to corner. The longer the distance, the more accurate the scale.

Glass surfaces (windows, glass doors) cannot be reconstructed photogrammetrically, however carefully you fly – these areas stay open in the model.

For professionals: ground control points and RTK

If you work with an RTK drone, a total station or a GNSS rover, you can also give Bleno surveyed ground control points. Bleno then calculates the model at true scale and plumb – measuring and taking measurements into the quote work without a reference distance, and the viewer shows how well the model fits the control points (mean residual error).

  • Lay out ground control points: at least 3, ideally 5, clearly visible targets, spread around the property and not in a line, also at different heights.
  • Survey each control point with a total station or GNSS rover and note the coordinates in the national grid (e.g. ETRS89 / UTM 32N, EPSG:25832).
  • After the flight, mark the control points on the photos in GCP Editor Pro or WebODM – each on at least 3 photos – and export the file gcp_list.txt.
  • In Bleno, choose “Passpunkt-Datei anhängen” (attach control point file) when uploading the photo series (admins only). Bleno checks the file straight away and runs a final check when processing starts: projection readable, at least 3 control points on at least 3 photos each, all named photos in the series.
  • Bleno recognises RTK drones (e.g. DJI Mavic 3 Enterprise RTK, Matrice with RTK module) from the photo data and shows “RTK-Serie erkannt” (RTK series detected). With a fixed solution, Bleno passes its accuracy on to the calculation. RTK alone does not replace the scale – that needs ground control points.

Format of the file gcp_list.txt (as required by OpenDroneMap): the first line is the projection – “EPSG:25832”, “WGS84 UTM 32N” or a PROJ string “+proj=utm +zone=32 …”; then one line per marking with easting, northing and elevation, the pixel position x and y in the photo, the image name and optionally the name of the control point, separated by spaces or tabs.

EPSG:25832
576104.12 5917329.55 31.20 2412 1730 DJI_0123.JPG gcp1
576104.12 5917329.55 31.20 1988 1102 DJI_0124.JPG gcp1
576120.40 5917330.08 31.45 1002 904 DJI_0131.JPG gcp2

How to set it up in your flight app

DJI Pilot 2
Only for the Enterprise class (Matrice/Enterprise series) – for Mini, Air and Mavic see Dronelink, Litchi or DJI Fly. In the map mode for area flights (waylines), mark the roof as an area, set overlap to about 75%/70% and choose a vertical gimbal pitch; for the oblique orbit use the orbit mode with a radius around the building and a gimbal pitch of 35–45° below the horizon. Do not create the low, almost horizontal orbit at 1–4 m as an automatic wayline: obstacle detection is limited during waypoint flights, so fly this pass by hand – as well as the second, closer orbit 2–3 m under the roof overhang (risk of collision, no automatic wayline). Add transition photos at medium height by hand in between.
Dronelink
Create the grid over the roof with the “Grid” component (overlap parameters at 75%/70%, camera vertical); for the orbits run the “Orbit” component with radius and camera angle as separate mission steps one after another – one oblique orbit, a second low and almost horizontal one. Do not create the second, closer orbit 2–3 m under the roof overhang as an automatic orbit component – fly it by hand (risk of collision, limited obstacle detection); transition photos at medium height also by hand. For the DJI Mavic 3 (without DJI MSDK), only the limited “Onboard Only” mode via DJI Fly is available, not full mission planning.
Litchi
Mission planner: set waypoints for the grid manually or by waypoint import, set the camera angle individually per waypoint (vertical for the grid), and for the orbits fly the circle function “Orbit Mode” in two passes with different radii and camera angles (oblique, then low and flat). Do not create the second, closer orbit 2–3 m under the roof overhang as a third “Orbit Mode” pass – fly it by hand (risk of collision, limited obstacle detection); transition photos at medium height also by hand. Litchi is not available for the DJI Mavic 3 (Classic/Pro) – no DJI MSDK.
Waypoints in DJI Fly
DJI Fly is the standard app for Mini, Air and Mavic (for the Enterprise class see DJI Pilot 2) and offers no automatic grid flight – set waypoints manually (save the course, place each point with a fixed height and camera angle) and ensure overlap yourself with closer point spacing; for orbits use the circle function or fly manually at a constant radius around the building. Fly the second, closer orbit 2–3 m under the roof overhang and the transition photos at medium height by hand rather than as a waypoint course. More work than in the other apps. DJI Fly offers waypoint flights only from the Mini 4 Pro; older models such as the Mini 3 do not have this function.

Your drone class

We list suitable apps per drone class as a starting point, not as complete proof of compatibility: whether your exact model supports an app – for example waypoint flights or the DJI MSDK access that Dronelink and Litchi need – depends on the model and firmware. Check this in the compatibility list of the app before the flight.

DJI Mini (e.g. DJI Mini 3, Mini 4 Pro)
Light (usually under 250 g) and sensitive to wind – postpone the flight in winds above about 20–25 km/h, otherwise image sharpness suffers in the orbit. Waypoint flights in DJI Fly are only available from the Mini 4 Pro; the Mini 3 does not have this function in DJI Fly.
Suitable apps: Dronelink, Litchi, Waypoints in DJI Fly
DJI Air (e.g. DJI Air 3)
A good compromise between stability and handling for most detached and semi-detached houses.
Suitable apps: Dronelink, Litchi, Waypoints in DJI Fly
DJI Mavic (e.g. DJI Mavic 3)
Larger sensor, more stable in wind – useful for larger properties or changeable weather. The Mavic 3 (Classic/Pro) has no DJI MSDK: Litchi therefore does not support it, and Dronelink only offers the limited “Onboard Only” mode via DJI Fly for it instead of full mission planning.
Suitable apps: Dronelink, Waypoints in DJI Fly
DJI Enterprise (e.g. DJI Matrice/Enterprise series)
For larger commercial properties and businesses with their own proof of competence for higher classes – grid flight and orbit work as with the smaller classes, usually with more accessories (spare batteries, RTK module) for longer series. Here you fly with DJI Pilot 2, not with DJI Fly, Dronelink or Litchi.
Suitable apps: DJI Pilot 2

Legal basics for drone flights

As of September 2026

This is an overview of publicly known rules for the EU and Germany, not legal advice. The regulations in force apply – please check them before every flight.

Operator registration
For a drone with a camera, registration as an operator is usually required in the EU (in Germany with the Federal Aviation Office, Luftfahrt-Bundesamt) – practically regardless of take-off weight, including the light class C0 with a camera; only pure toy drones are exempt. The registration number is attached to the drone.
EU proof of competence A1/A3
From a take-off weight of 250 g or from class C1, the EU A1/A3 proof of competence (online test) is added to the registration. Heavier classes and flights closer to people require further certificates.
Insurance
In Germany, drone flights require liability insurance that explicitly covers drones – a standard personal liability policy usually does not cover drones.
Geo-zones
Check the current geo-zones before every flight (airports, emergency operation areas, nature reserves, residential properties and other restricted zones or zones with conditions). Flight apps usually show the zones but do not replace your own check.
Privacy of neighbouring properties
Special rules apply over other people's properties – especially inhabited neighbouring properties: photos and videos must not simply capture people or other people's property in an identifiable way. In Germany, flying over residential properties with a camera drone requires the explicit consent of the owner or occupant (section 21h(3) no. 7 LuftVO) – obtain it before the flight, do not just inform them, and keep the flight to the property you are working on wherever possible.

Available today: roof measurements from a drone photo

Until Bleno 3D launches, you can measure roof areas directly from an overhead drone photo with digital measurements – included in every Bleno plan.